Notice:
Noticed: IR1 is the signal of RX1 with inverter ,used for SBUS receiver.
RX1 and IR1 couldn’t be used at the same time .
CrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s.
It’s a better upgrade flight controller for your whoops. We could use this flight controller to building a 1s-2s compatible lightest 65mm/75mm/85mm brushless whoop.
Important: Not compatible with big propeller like 65mm/75mm when use 2s battery .
Recommend max size of propeller is 55mm.
Camera is NOT Included.
Specification:
Brand Name: Happymodel
Model: Crazybee X V1.0
Item Name: F4 1-2S FC AIO ESC VTX & Receiver Board
F4 Flight Controller | MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1S-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky receiver support D8/D16 Built-in 5V 1A BEC Built-in voltage detection Firmware target: CRAZYBEEF4FR |
Onboard 5A BL_S 4in1 ESC | EFM8BB21 Power supply: 1-2S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_90_REV16_7.HEX Default protocol: DSHOT600 |
Onboard SPI Frsky Receiver | SPI BUS receiver Frsky D8/D16 compatible Support Frsky_X_LBT(EU-LBT), Fubata S-FHSS (Need Betaflight 4.0.5 firmware or latest) Channels: 8ch/16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m |
Onboard 5.8G 40CH 25mW VTX | Output power: 25mw Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready Default vtx_power should set to be “2” |
Onboard Voltage and Current detector |
Voltage Meter scale “110” Amperage Mete scale “1175” |
Bind Procedure
1. Make the on board receiver get into bind mode: For 3.5.7 version firmware Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
2. Make your transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio , but the bind is actual successful , need to go to CLI command and type “save” to finish the binding .
SPI Receiver option:
Frsky_D compatible with Frsky D8 protocol
Frsky_X compatible with Frsky non-eu D16 protocol
Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
SFHSS compatible with Fubata S-FHSS protocol
Pacakage Included:
1x Happymodel Crazybee X V1.0 Flight Controller AIO Board
1x Cable
4x Anti-Vibration Ball
4x Screws